Comparing microphone sensitivity ratings: what does it mean?
What is microphone sensitivity?
A microphone sensitivity specification tells how much electrical output (in thousandths of a volt or \"millivolts\") a microphone produces for a certain sound pressure input (in dB SPL). If two microphones are subject to the same sound pressure level and one puts out a stronger signal (higher voltage), that microphone is said to have higher sensitivity. However, keep in mind that a higher sensitivity rating does not necessarily make a microphone better than another microphone with a lower sensitivity rating.
What is \"dB SPL\"?
The term \"dB SPL \" is a measurement of Sound Pressure Level (SPL) which is the force that acoustical sound waves apply to air particles. As a person talks or sings, SPL is strongest near the mouth and weakens as the acoustical waves move away from the person. As reference levels, 0 dB SPL is the quietest sound a human can normally hear and 1 dB is the smallest change in level that the human ear can detect. For comparison, at three feet, speech conversation level is about 60 dB SPL and a jackhammer\'s level is about 120 dB SPL.
What about dB SPL input levels?
Microphone manufacturers normally specify one of two dB SPL input levels: 74 dB SPL or 94 dB SPL. Shure uses 74 dB SPL unless indicated otherwise on the data sheet. How do these dB SPL values relate to the real world? 74 dB SPL is typical of the sound intensity twelve inches away from a talker. 94 dB SPL is typical of the sound intensity one inch away from the same talker. A microphone \"hears\" these sound intensities and converts the acoustic wave into an equivalent electrical signal. To determine which SPL is used for a sensitivity measurement, look at the microphone data sheet. Confusion can arise because of the different units by which SPL may be specified. For example, 94 dB SPL = 1 Pascal = 10 microbars = 10 dynes/cm2. And 74 dB SPL = 0.1 Pascal = 1 microbar = 1 dyne/cm2. Unfortunately for the microphone buyer, different manufacturers use different units to specify SPL. But by following these dB SPL unit conversions, you can determine how different dB SPL ratings relate to each other.
What does \"open circuit voltage rating\" mean?
First, \"open circuit\" means the microphone is not connected to anything. That is, there is no electrical load on the microphone. The open circuit voltage rating indicates how much voltage appears at the microphone output when a certain SPL is introduced to the microphone diaphragm. A value for a typical dynamic mic is -75 dBV/microbar. The \"V\" in dBV indicates the microphone output level is referenced to 1 Volt. If there was a microphone with an output voltage of 1 volt, its level would be given as 0 dBV. The negative dBV output level (\"-75\") indicates that the mic output voltage is less than 1 volt (-75 dBV converts to .00018 volts). The \"microbar\" part indicates the microphone was tested with an input of 74 dB SPL. (Please reread the preceding section if the conversion from 1 microbar to 74 dB SPL is confusing.) To compare this typical dynamic microphone\'s sensitivity with a different microphone that was tested at 94 dB SPL or 1 Pascal, simply add 20 dB to the rating: -75 + 20 = -55 dBV/Pascal. Remember, to compare specifications from different manufacturers, make certain that each has been converted to the same input dB SPL level.
What is a microphone power rating?
To get a power rating, a microphone is attached to a load equal to its own internal resistance. The microphone is subjected to 94 dB SPL and the resulting power output across the load is measured. Power ratings have virtually no relevance to today\'s audio circuits and are now rarely used.
As with any dynamic microphone, the SM58 vocal microphone is tailored to target the sound it is pointing directly at, this helps minimise any background noise caused by other instruments or back ground music making it a firm favorite with live venues, DJ's and musicians. Shure SM58 Microphone Key Features: Frequency response tailored for vocals, with…
An embossed single-diaphragm, side-address, cardioid condenser microphone for highly critical studio recording and live sound productions. The Shure KSM32 offers an extended frequency response for an open, natural sounding reproduction of the original sound source. Features: Class A, transformerless preamplifier circuitry eliminates cross-over distortion for improved linearity across the full frequency range. Embossed, high-compliance…
Availability:Normally 7-10 Days
The new standard for home recording and the music industry. The mic for everyone who, despite budget limitations, does not want to do without the uncompromising Neumann sound. Cardioid directional characteristic and very low self-noise. The TLM 103 is the ideal large diaphragm microphone for all professional and semi-professional applications requiring the utmost in sound quality on a limited budget.…
Availability:Call 0844 815 0888
The e 835 is a cardioid lead vocal stage microphone specially designed to perform under pressure. Sound inlet basket: refined steel. Features Rugged metal body Excellent feedback rejection High sound pressure handling capability Shock-mounted capsule provides excellent suppression of handling noise Uniform onand off-axis response Cardioid pick-up pattern provides isolation from other on-stage signals…
Availability:Call 0844 815 0888