Feelin' Groovy? Groove Tubes now on Dolphin Music
Guitarists both yesterday and today can be linked by one piece of equipment: The tube amp. With all the strides in transistor amp technology, guitarists still prefer tube amps. Why do tube amp designs sound and feel differently from solid-state? Simply, tubes work differently.
What is a tube?
A tube is an electronic device consisting of a minimum of four active elements: a heater (filament), a cathode, a grid and a plate. All sealed in a vacuum glass enclosure to prevent parts from burning. Once heated, the cathode begins to emit electrons, which flow from the cathode (which is negatively charged) toward the plate (which is positively charged). The grid's purpose is to control this flow, in effect, acting as a valve.
How do Tubes Work?
When the guitar's pickup produces a small voltage (the result of the string vibrating in the pickup's magnetic field), this signal is applied to the grid, which causes a large current flow from the cathode to the plate.
Because of this, a correspondingly large voltage now appears at the plate. A portion of the amp's electronic circuitry, the grid bias control, adjusts the proper voltage setting of the grid. When the grid bias is properly set, the tube is balanced to the circuit, and therefore produces a clean, powerful signal. The plate is connected to an output transformer, which matches the impedance to that of the speaker.
How do Tubes Distort?
As the signal emitting from the plate approaches its maximum potential, the tube gradually begins to react less and less to the original input signal. This results in a type of compression of the signal, and the signal becomes cut off or "clipped." Tube distortion ("clipping") occurs gradually, producing low order distortion which compliments the original signal, creating a warm sound. This is also why it's easy to move between clean and distorted tones.
The Groove Tubes Process:
Analyzing and Selecting tubes.
Groove Tubes literally go through thousands of tubes, rejecting more tubes than they accept. Groove Tubes put every tube through a rigorous performance test, one at a time, in real amp circuits. The preamp tubes are rejected for adverse microphonics, low output or high noise. Power tubes are more involved, and they go through additional analysis. Here's what they're looking for:
- Grid Leakage. Causes tube to burn out quickly, and worse yet, to short out and wreak lots of havoc. Groove Tubes throw these tubes out.
- Weak Vacuum. Tube will act deceptively normal, then just burn out on you (usually at the worst time!). These tubes don't make it past the first round.
- Gain to Distortion Ratio. The center of all Groove Tube magic! This measurement tells them if the tube will distort early or later in its power range. Since the tube distortion is rich in harmonics (That's why we love 'em!), the tonality of each tube will vary according to this ratio. Only Groove Tubes sets have been measured and matched to insure longer sustain, wider frequency response and a more musical amplifier!
- Rating and Matching Tubes. Groove Tubes translate this gain to distortion ratio into a performance scale that can range up to 100 points, then match up the tubes to within 1 point of each other. To simplify things, they reduce the scale to 1-10 before the tubes leave the shop. All tubes are exactly matched into duets, quartets, sextets and even octets.
More than just Great Tone.
The Groove Tubes Process produces many welcomed improvements:
- Dramatically Improved Sustain by eliminating phase cancellation (which occurs when dissimilar tones coming from unmatched tubes are combined and cancel out certain frequencies.)
- Improved Harmonic Balance- All the notes you play will have the same amplitude. (No more dead spots or dull notes!)
- Longer Life Span by 1st) eliminating faulty tubes. 2nd) Our balanced sets reduce stress that occurs when a stronger tube is working too hard to make up for its weaker partner, and 3rd) because our sets drive the output transformer evenly it actually runs cooler!
Why do Tube Amps all Sound Different?
Types and quality of tubes vary, some tubes amplify more than others.
The amount of gain a tube produces varies with the each amp's circuit design, some tubes amplify more than others under similar conditions.
The 4 amp stages:
- Preamp Stage - Amplifies an incoming guitar or mic signal for tone shaping.
- Signal Processing Stage -This is where you add the effects, reverb, tone controls, etc.
- Power Amp Stage -The real workers in your amp. Most amps over 10 watts use an alternating push/pull power amp design- when one tube is on, the other is off. Your amp may have two, four, six or possibly eight power tubes.
- Rectifier Stage -Converts AC wall electricity to the DC electricity inside your amp. Most modern amps have sold state rectifiers.
Why Should You Replace Your Tubes?
Glass, metal, lots of little parts... tubes are subject to mechanical problems and are not meant to last a lifetime. Actually, the harder you work your tubes, the faster they wear out. Which means that from time to time you will need to replace your tubes. More reasons to replace your tubes:
When one starts to go, it drags the others down with it, decreasing the over all efficiency of the amp.
The better the tube, the better the tone. Simply put, the best reason to replace your tubes with Groove Tubes is that they'll make your amp sound better.
Pay attention to your amp's performance. When you hear the sound begin to deteriorate, it's time to change your tubes. Your amp will last longer. Your tone will always be at its best. Think about it, you don't wait until the strings break before you change them, do you? Look for these signs that Your Tubes May be Deteriorating:
- Loss of highs or lows, Muddy chords
- Poor balance in the output of various notes
- Lacks punch, Makes funny noises
- Amp starts sounding weak
- Power fading up and down
- No sustain, or fast decay
New European version with even more response, higher power and warmer tone. Most common low power pentone, popularized in early Vox AC30 amps. Rediscovered by Matchless amps and now currently used by nearly every tube amp company. Quick, soft overdrive distortion, great for recording but usually too low volume for live gigs. GT Rating System: 1-3 (Low) Understanding…
New exclusive GT design with special "heat wings" attached to plate for more power, longer life, and better tone. Big bottom, very dynamic, most powerful in it's class. Our own exclusive specially modified power pentode with 15% more power and great overall tone. Big heat sinks attached to the plates keep this one from "sagging" at full power and so…
12AT7. Used for phase inverters in many amps such as Fender Black and Silver Face, reverb drivers, etc. This tube is used widely in most of the US-made amps and, in particular, the Fender amps. Fender amps with reverb use two 12AT7s - one for the reverb drive stage, and one used as a phase inverter to drive the push/pull…
Availability:Normally 3-5 Days
A Chinese version of the 12AX7-C. Great for Marshalls and Fenders. Sweet warm mid range tone, complements tone of European amps. A tube that takes some of the edge off of high gain amps by reducing the brightness while still having the gain and articulation. For those that change first stage gain preamp tubes to change the taste and…
Availability:Normally 3-5 Days
Reproduction of a classic EL-34 XF2 Dual Getter tube. This is a classic. The GT-EL34M was shown at NAMM. This tube is based upon a tube which is considered something of an icon to EL34 users in both the audio world and guitar amp world. There were a number of variants of the original tube and GT chose the classic…